155 lines
7.3 KiB
TeX
155 lines
7.3 KiB
TeX
\chapter{Impact to the COMET Phase-I}
|
|
\label{cha:discussions_on_the_impact_to_the_comet_phase_i}
|
|
The measured proton emission rate of 3.5\% is about 5 times
|
|
smaller than the figure using to make the baseline design of the CDC in COMET
|
|
Phase-I. The spectrum shape is softer than that of silicon,
|
|
peaks around \SI{4}{\MeV} rather than at \SI{2.5}{\MeV}
|
|
(\cref{fig:sobottka_spec}). Therefore CDC hit rate due to proton should be
|
|
smaller than the current estimation.
|
|
|
|
The CDC proton hit rate is calculated by a toy MC study. The dimensions of the
|
|
geometry shown in \cref{fig:cdc_toy_mc} are from \cref{ssub:CDC_configuration}.
|
|
The inner wall of the CDC is \SI{0.5}{\mm} thick CFRP.
|
|
A proton absorber made
|
|
of CFRP is placed \SI{5}{\cm} far from the inner wall of the CDC. The
|
|
absorber's thickness is varied from 0 (no absorber) to \SI{1}{\mm}.
|
|
\begin{figure}[htb]
|
|
\centering
|
|
\includegraphics[width=0.55\textwidth]{figs/cdc_toy_mc}
|
|
\caption{Geometry of the toy MC study for hit rate study.}
|
|
\label{fig:cdc_toy_mc}
|
|
\end{figure}
|
|
|
|
The protons with the energy spectrum shape as in
|
|
\cref{sub:proton_emission_rate} are generated inside the COMET's muon stopping
|
|
targets which are 17 200-\si{\um}-thick aluminium discs. The spatial
|
|
distribution of protons resembles the stopping distribution of muons inside the
|
|
target discs calculated from the full MC simulation of the COMET detectors
|
|
(\cref{fig:cdc_toy_mc_init_pos}).
|
|
\begin{figure}[htb]
|
|
\centering
|
|
\includegraphics[width=0.65\textwidth]{figs/cdc_toy_mc_init_pos_xy}
|
|
\includegraphics[width=0.60\textwidth]{figs/cdc_toy_mc_init_pos_z}
|
|
\caption{Spatial distribution of the generated protons in X, Y (top) and
|
|
Z (bottom). Z is the axis of the CDC, X, Y are the horizontal and vertical
|
|
axes respectively.}
|
|
\label{fig:cdc_toy_mc_init_pos}
|
|
\end{figure}
|
|
|
|
The protons are then tracked in a \SI{1}{\tesla} magnetic field. The protons
|
|
reaching the absorber, inner wall and the sensitive volume of the CDC are
|
|
recorded (see \cref{fig:cdc_toy_mc_p_spec_500um}).
|
|
\begin{figure}[!htb]
|
|
\centering
|
|
\includegraphics[width=0.75\textwidth]{figs/cdc_toy_mc_p_spec_500um}
|
|
\caption{Proton energy spectra at different stages from birth to the
|
|
sensitive volume of the CDC. The baseline design of \SI{0.5}{\mm} thick
|
|
absorber and \SI{0.5}{\mm} thick inner wall was used to produce this
|
|
plot.}
|
|
\label{fig:cdc_toy_mc_p_spec_500um}
|
|
\end{figure}
|
|
|
|
A muon stopping rate of \SI{1.3E9}{\Hz} is assumed as in the COMET Phase I's
|
|
TDR. The number of proton emitted is then $\num{1.3E9} \times 0.609 \times
|
|
0.035 = \SI{2.8E7}{\Hz}$. The hit rates on a single cell in the inner most
|
|
layer due to these protons with
|
|
different absorber configurations are listed in
|
|
\cref{tab:proton_cdc_hitrate_comp}.
|
|
|
|
\begin{table}[htb]
|
|
\begin{center}
|
|
\begin{tabular}{S S S S S}
|
|
\toprule
|
|
{\textbf{Absorber}} &{\textbf{Inner wall}} & {\textbf{Total CFRP}}&
|
|
{\textbf{Proton hit rate}} & {\textbf{Proton hit rate}}\\
|
|
{\textbf{thickness}} &{\textbf{thickness}} & {\textbf{thickness}}&
|
|
{\textbf{Phase-I TDR}} & {\textbf{New estimation}}\\
|
|
{(\si{\mm})} & {(\si{\mm})} & {(\si{\mm})} & {(\si{\Hz})}& {(\si{\Hz})}\\
|
|
\midrule
|
|
1 &0.5&1.5 & 4E+3 & 2 \\
|
|
0.5 &0.5&1.0 & 11E+3& 126 \\
|
|
0 &0.5&0.5 & 30E+3& 1436 \\
|
|
\bottomrule
|
|
\end{tabular}
|
|
\end{center}
|
|
\caption{CDC proton hit rates in this study in comparison with the expected
|
|
rates in COMET Phase-I's Technical Design Report~\cite{COMET.2014} at
|
|
different configurations of proton absorber and inner wall.}
|
|
\label{tab:proton_cdc_hitrate_comp}
|
|
\end{table}
|
|
|
|
%\begin{table}[htb]
|
|
%\begin{center}
|
|
%\begin{tabular}{S S S S S S}
|
|
%\toprule
|
|
%{\textbf{Absorber}} &{\textbf{Inner wall}} & {\textbf{Total CFRP}}& {\textbf{Proton}} & {\textbf{Momentum}} & {\textbf{Integrated charge}}\\
|
|
%{\textbf{thickness}} &{\textbf{thickness}} & {\textbf{thickness}}& {\textbf{hit rate}} &{\textbf{spread $\Delta p$}} &{\textbf{300 days}}\\
|
|
%{(\si{\mm})} & {(\si{\mm})} & {(\si{\mm})} & {(\si{\Hz})} & {(\si{\keV\per\hepclight)}} &{(mC/cm)}\\
|
|
%\midrule
|
|
%1 &0.5&1.5 & 2 & 195 & 25\\
|
|
%0.5 &0.5&1.0 & 126 & 167 & 60\\
|
|
%0 &0.5&0.5 & 1436 & 133 & 160\\
|
|
%\bottomrule
|
|
%\end{tabular}
|
|
%\end{center}
|
|
%\caption{CDC proton hit rates at different configuration of proton absorber
|
|
%and inner wall. The momentum spreads for \SI{0.5}{\mm} thick inner wall are
|
|
%taken from \cref{tab:comet_absorber_impact}.}
|
|
%\end{table}
|
|
At the baseline design of \SI{0.5}{\mm}, the hit rate is only \SI{126}{\Hz},
|
|
much smaller than the current estimation at \SI{11}{\kHz}. Even without the
|
|
absorber, proton hit rate remains lower than that level at \SI{1.4}{\kHz}.
|
|
Therefore the absorber is not necessary as far as the hit rate is concerned.
|
|
%Therefore a proton
|
|
%absorber is not needed for the COMET Phase I's CDC.
|
|
|
|
If the proton absorber is not used, the momentum spread of the signal electron
|
|
reduces from \SI{167}{\keV\per\hepclight} to \SI{131}{\keV\per\hepclight} (\cref{tab:proton_cdc_hitrate}).
|
|
This is a small improvement since the momentum resolution is dominated by
|
|
intrinsic spread of \SI{197}{\keV\per\hepclight} due to multiple scattering in gas
|
|
and wires.
|
|
|
|
The last column of \cref{tab:proton_cdc_hitrate} shows the integrated charge
|
|
per unit length of a wire. The TDR deems an integrated charge level of
|
|
\SI{200}{\milli\coulomb\per\cm} safe. So even with the pessimistic estimation using
|
|
silicon rate and spectrum and without the proton absorber, the integrated
|
|
charge level in the CDC is still below the requirement. Therefore removing the
|
|
absorber will not worsen the ageing process of the wires.
|
|
\begin{table}[htb]
|
|
\begin{center}
|
|
\begin{tabular}{S S S S S}
|
|
\toprule
|
|
{\textbf{Absorber}} &{\textbf{Inner wall}} & {\textbf{Total CFRP}}&
|
|
{\textbf{Momentum}} & {\textbf{Integrated charge}}\\
|
|
{\textbf{thickness}} &{\textbf{thickness}} & {\textbf{thickness}}&
|
|
{\textbf{spread $\Delta p$}} &{\textbf{300 days}}\\
|
|
{(\si{\mm})} & {(\si{\mm})} & {(\si{\mm})}
|
|
& {(\si{\keV\per\hepclight)}} &{(mC/cm)}\\
|
|
\midrule
|
|
1 &0.5&1.5 & 195 & 25\\
|
|
0.5 &0.5&1.0 & 167 & 60\\
|
|
0 &0.5&0.5 & 133 & 160\\
|
|
%0 &0.3&0.3 & 8281 & {-} & {-}\\
|
|
%0 &0.1&0.1 & 15011& {-} & {-}\\
|
|
\bottomrule
|
|
\end{tabular}
|
|
\end{center}
|
|
\caption{Momentum spreads due to the inner wall and absorber, and integrated
|
|
charge per unit length of wire as calculated in the COMET Phase-I's TDR.
|
|
The momentum spreads were calculated for signal electrons at
|
|
\SI{104.96}{\MeV\per\hepclight}. The integrated charge is estimated assuming 300
|
|
days of operation.}
|
|
\label{tab:proton_cdc_hitrate}
|
|
\end{table}
|
|
|
|
%In case a lower momentum spread is desired, it is possible to reduce the
|
|
%thickness of the inner wall. The last
|
|
%two rows of \cref{tab:proton_cdc_hitrate} show that even with thinner walls at
|
|
%\SI{0.3}{\mm} and \SI{0.1}{\mm} the hit rate by protons are still at
|
|
%manageable levels. However, reducing the wall thickness would be governed by
|
|
%other requirements such as mechanical structure and gas-tightness.
|
|
In summary, the toy MC study with the preliminary proton rate and spectrum
|
|
shows that a proton absorber is not needed. It confirms the known fact that the
|
|
estimation used in COMET Phase-I is conservative, and provides a solid
|
|
prediction of the hit rate caused by protons.
|